how to move plumbing lines for a washing machine

Adjust the feet by twisting them counter-clockwise to raise the washer clockwise to lower it. See below for a shopping list and toolsSUBSCRIBE to This Old Hou.

Convert An Unfinished Laundry Area Into A Laundry Room

If your walls are not finished the studs are exposed or if you are able to run pipes through walls you can install a washing.

. Dead-legs dont have much water movement so can become harbours for bacteria which will then get into the rest of the plumbing system. Depending on how close it is to the existing plumbing that price could be. Secure the washer to the dolly with ropes.

Washing machines typically require a 2-inch drain line with a vent. Run new hot- and cold-water copper pipes to the wood-stud wall. Attach an ABS pipe measuring two inches long to the wall where the washing machine will be installed.

Your washing machine cut-off valve will likely cost around 10 to 30 for each line. Keep the machine upright as you wheel it through and out of the house. Drape the drain hose over the side of the utility sink and clamp it firmly in place.

Water lines Dont leave dead-legs or dead-ends so depending on where youre coming from you should cut and cap the lines as close to the supply as possible eg 1 away. Horizontal drains need to have a minimum grade of 14 per foot. Can you move a washing machine without transit bolts.

If you are using a water softener you will need to add a small amount of distilled water to your water supply. The washing machine usually includes this. Building a Drain Line for the Washer.

Drain height for a laundry tray is 18-12 from the floor. Does a washing machine need to be drained before moving. Once this is done you have finished plumbing the water supply.

From the trap the waste pipe must run through your outside wall to a hopper head or gully or directly into a soil stack. Regardless of whether you are installing a standpipe or a laundry tray to drain the washing machine you will need to locate and tie into an existing gravity drainage system and vent the trap. Front to back and side to side.

Relocating your washing machine gets trickier when plumbing costs are involved. And one major plumbing cost to relocate your washer and dryer is building a drain line. Hold the blankets in place with a cord or packing tape.

The vent must be within 60 inches of the P-trap for a 2-inch drain. Move washing machine out of the way and build a wood-stud wall against the basement wall. The drain piping starts with a standpipe a vertical pipe that connects to a P-trap at the bottom and is open at the top to receive the washing machines drain hose.

Use extra tape to secure it so that no tripping accidents occur while moving the washing machine with a dolly. The washer should have a special bracket for holding that drain hose. Attach plywood panel to the upper half of the wood-stud wall using 1⅝-inch screws.

Set the washing machine in place and level it. Install the transit bolts in the washer. Extend hot- and cold-water copper pipes down the face of the plywood panel.

This ones going to be connected to the vent pipe. Turn off the hot and cold water leading to the washing machine. Twist on the connector from the hot water faucet to the hot water outlet on the back of the machine.

Set the pipe two inches from the adjacent wall and about 36 inches from the ground. This Old House plumbing and heating expert Richard Trethewey re-plumbs a washing machine. Your washing machine will need to be level for it to properly function.

One option is to hook the hose into the top of an open standpipe with a P-trap at its base. A spirit level can be placed on the washing machines top to ensure it is a level surface use the spirit level in both directions. The air gap at the top of the standpipe will stop any dirty water siphoning back into the machine.

There should also be an outlet from a two-inch sanitary tee thatll face upward. Before moving shipping or storing youll need to drain excess liquid from all parts of the machine. Attach the drain hose to the drain hole beside the water inlet valve by bending it into a u-shape.

Screw the machines supply lines to the valves and tighten with pliers. Yes you can but you shouldnt. After youve connected the hoses to the water supply faucets or shut off valves you will connect the hoses to the rear of the washing machine.

The main ventilating system should be connected to the drain hole. Once the machine is properly drained or winterized storing it properly particularly if for a long period of time is the key to having a washer thats ready to go back into. Next get your helper or helpers to carefully lift your machine onto a dolly.

Do the same for the cold water hoses.

Washing Machine P Trap And Drain